Search This Blog

Showing posts with label Technology. Show all posts
Showing posts with label Technology. Show all posts

Sunday, March 17, 2019

'T Power H20,' the Eco-Friendly Bike

NAMED the 'T Power H20,' the eco-friendly bike was created by Ricardo Azevedo in Sao Paulo. The design features a combination of water and a single, external car battery used to produce electricity and separate the hydrogen from the water molecule. The process, involving a pipe-system, results in combustion which subsequently creates the energy necessary to power the bike.
The motorcycle does not need clean drinking water to run, and Azevedo demonstrated this when he went to the Tiete River, a river that is polluted, and filled the motorcycle up from that. He has been talking about the environmental benefits of his H20 motorcycle and of course the benefits of the cost associated with running a motorcycle that does not require fuel.
He said that one advantage of the motorcycle only using water to run was that it works with hydrogen that comes from the water and this means that the only thing that comes out of the exhaust pipe of the motorcycle is water vapour. He went on to point out that this is unlike a traditional motorcycle running on fuel which sends out carbon monoxide.

Sunday, September 24, 2017

Urban Rainwater Harvesting

Introduction

Rainwater harvesting (RWH) is a simple technique that offers many benefits. It can be done very low-tech, doesn’t cost much and is applicable at small-scale with a minimum of specific expertise or knowledge; or in more sophisticated systems at large-scale (e.g. a whole housing area).The most common technique in urban areas (besides storm water management) is rooftop rainwater harvesting: rainwater is collected on the roof and transported with gutters to a storage reservoir, where it provides water at the point of consumption or is used for groundwater recharge (see also surface and subsurface artificial groundwater recharge). Collected rainwater can supplement other water sources when they become scarce or are of low quality like brackish groundwater or polluted surface water in the rainy season. It also provides a good alternative and replacement in times of drought or when the water table drops and wells go dry. The technology is flexible and adaptable to a very wide variety of conditions. It is used in the richest and the poorest societies, as well as in the wettest and the driest regions on our planet (HATUM & WORM 2006).

Basic Design Principles

Rooftop rainwater harvesting system.Source: CPREEC (Editor) (n.y.)
Each rainwater harvesting system consists of at least the following components (INFONET-BIOVISION 2010):

  1. Rainfall

  2. A catchment area or roof surface to collect rainwater.

  3. Delivery systems (gutters) to transport the water from the roof or collection surface to the storage reservoir.

  4. Storage reservoirs or tanks to store the water until it is used.

  5. An extraction device (depending on the location of the tank - may be a tap, rope and bucket, or a pump (HATUM & WORM 2006); or a infiltration device in the case the collected water is used for well or groundwater recharge (see also surface or subsurface artificial groundwater recharge)

Additionally there are a wide variety of systems available for treating water either before, during and/or after storage (e.g. biosand filter, SODIS, chlorination; or in general HWTS).

Process diagram of a drinking water RWH system.Source: THOMAS & MARTINSON (2007)
Illustration of water flow scheme of a RTRWH system. Basic components: roof, gutters, first flush device (first rain separator), rain barrel with filter and tap and recharge well. Source: RAINWATERCLUB (Editor) (n.y.)

Rainfall


Table 1: Average Annual Rainfall in different regions. Source: HATUM & WORM (2006)
The rainfall pattern over the year plays a key role in determining whether RWH can compete with other water supply systems. Tropical climates with short (one to four month) dry seasons and multiple high-intensity rainstorms provide the most suitable conditions for water harvesting. In addition, rainwater harvesting may also be valuable in wet tropical climates (e.g. Bangladesh), where the water quality of surface water may vary greatly throughout the year. As a general rule, rainfall should be over 50 mm/month for at least half a year or 300 mm/year (unless other sources are extremely scarce) to make RWH environmentally feasible (HATUM & WORM 2006). In the following table, some examples are given for annual rainfall in different regions (HATUM & WORM 2006).

Catchment Area

To be ‘suitable’ the roof should be made of some hard material that does not absorb the rain or pollute the run-off. Thus, tiles, metal sheets and most plastics are suitable, while grass and palm-leaf roofs are generally not suitable (THOMAS & MARTINSON 2007).

Delivery System


A variety of guttering types. Source: HATUM & WORM (2006)
The delivery system from rural rooftop catchment usually consists of gutters hanging from the sides of the roof sloping towards a down pipe and tank. Guttering is used to transport rainwater from the roof to the storage vessel. Guttering comes in a wide variety of shapes and forms, ranging from the factory made PVC type similar as the pipes used in water distribution systems) to home made guttering using bamboo or folded metal sheet. Guttering is usually fixed to the building just below the roof and catches the water as it falls from the roof (HATUM & WORM 2006).


Example of a first flush device (white, vertical PVC pipe, left). Illustration of the working principle of the device (right). Source: DOLMAN & LUNDQUIST (2008)
Debris, dirt, dust and droppings will collect on the roof of a building or other collection area. When the first rains arrive, this unwanted matter would be washed into the tank. This will cause contamination of the water and the quality will be reduced. Many RWH systems therefore incorporate a system for diverting this ‘first flush’ water so that it does not enter the tank. These systems are called first flush devices. Further information on first flush devices is provided in DOLMAN & LUNDQUIST (2008) and PRACTICAL ACTION (2008).



Left: this filter (developed by WISY) fits into a vertical down pipe and acts as both filter and first-flush system. Right: filter cartridge of Pop-up-filter (developed by KSCST) acts as a first-flush separator. Source: CSE (n.y.), KSCST (n.y.)
The simpler ideas are based on a manually operated arrangement whereby the inlet pipe is moved away from the tank inlet and then replaced again once the initial first flush has been diverted. This method has obvious drawbacks in that there has to be a person present who will remember to move the pipe. Other, more sophisticated methods provide a much more elegant means of rejecting the first flush water, (described in PRACTICAL ACTION (2008), training material). But practitioners often recommend that very simple, easily maintained systems be used, as these are more likely to be repaired if failure occurs (PRACTICAL ACTION 2008).
A coarse filter, preferably made of nylon or a fine mesh, can also be used to remove dirt and debris before the water enters the tank (HATUM & WORM 2006).

Storage Tanks


RTRWH in Urban Areas using a Plastic Tank. Source: VISHWANATH (n.y.)
There are almost unlimited options for storing rainwater. Common vessels used for very small-scale water storage in developing countries include plastic bowls and buckets, jerry cans, clay or ceramic jars, cement jars, old oil drums, empty food containers, etc. For storing larger quantities of water, the system will usually require a tank above or below ground. These can vary in size from a cubic metre (1000 litres) up to hundreds of cubic metres for large projects (PRACTICAL ACTION 2008). For domestic systems volumes are typically up to a maximum of 20 or 30 cubic metres (PRACTICAL ACTION 2008). Surface tanks are most common for roof collection. Materials for surface tanks include metal, wood, plastic, fibreglass, brick, inter-locking blocks, compressed soil or rubble-stone blocks, ferro-cement and reinforced concrete. The choice of material depends on local availability and affordability. The material and design for the walls of sub-surface tanks or cisterns must be able to resist the soil and soil water pressures from outside when the tank is empty. Tree roots can damage the structure below ground. Careful location of the tank is therefore important (HATUM & WORM 2006).
There are a number of different methods used for sizing the tank. These methods vary in complexity and sophistication. PRACTICAL ACTION (2008) gives an overview over three different methods. Some are readily carried out by relatively inexperienced, first-time practitioners, while others require computer software and trained engineers who understand how to use this software. The storage requirement will be determined by a number of interrelated factors, which include: local rainfall data and weather patterns, size of roof, runoff coefficient (depending on roof material and slope) and user numbers and consumption rates.
In reality the cost of the tank materials will often govern the choice of tank size. In other cases, such as large RWH programmes, standard sizes of tank are used regardless of consumption patterns, roof size or number of individual users (although the tank size will, hopefully, be based on local averages) (PRACTICAL ACTION 2008).

Infiltration

Collected water can also be used for replenishing a well or the aquifer (see also surface or subsurface artificial groundwater recharge). In a case study of SHRESTHA (2010), excess rainwater during the rainy season is used to recharge a dug well, as well as the groundwater. In this case recharging the groundwater even improved the water quality in the dug well.

User Behaviour

Depending on the user behaviour the storage and treatment (water quality) infrastructure is probably different. In some parts of the world, RWH is only used to collect enough water during a storm to save a trip or two to the main water source (open well or pump). In this case only a small storage container is required. In arid areas, however, people strive to create sufficient catchment surface area and storage capacity to provide enough water to meet all the needs of the users (HATUM & WORM 2006).
Four types of user regimes can be discerned:
Occasional - Water is stored for only a few days in a small container. This is suitable when there is a uniform rainfall pattern and very few days without rain and there is a reliable alternative water source nearby.
Intermittent - There is one long rainy season when all water demands are met by rainwater, however, during the dry season water is collected from non-rainwater sources. RWH can then be used to bridge the dry period with the stored water when other sources are dry.
Partial - Rainwater is used throughout the year but the ‘harvest’ is not sufficient for all domestic demands. For instance, rainwater is used for drinking and cooking, while for other domestic uses (e.g. bathing and laundry) water from other sources is used.
Full - Only rainwater is used throughout the year for all domestic purposes. In such cases, there is usually no alternative water source other than rainwater, and the available water should be well managed, with enough storage capacity to bridge the dry period.

Cost Considerations

Run-off from a roof can be directed with little more than a split pipe or piece of bamboo into an old oil drum (provided that it is clean) placed near the roof. The water storage tank or reservoir usually represents the biggest capital investment element of small-scale rooftop urban rainwater harvesting system and therefore require careful design to provide optimal storage capacity while keeping the cost as low as possible. Installing a water harvesting system at household level can cost anywhere from USD 100 up to USD 1000. It is difficult to make an exact estimate of cost because it varies widely depending on the availability of existing structures, like rooftop surface, pipes and tanks and other materials that can be modified for a water harvesting structure. Expensive systems with large tanks deliver more water than cheaper systems with small tanks (THOMAS & MARTINSON 2007).

Health Aspects

Rainwater itself is of excellent quality, only surpassed by distilled water – it has very little contamination, even in urban or industrial areas, so it is clear, soft and tastes good. Contaminants can however be introduced into the system after the water has fallen onto a surface (THOMAS & MARTINSON 2007).
Firstly, there is the issue of bacteriological water quality. Rainwater can become contaminated by pathogenic bacteria (e.g. form animal or human faeces) entering the tank from the catchment area. It is advised that the catchment surface always be kept very clean. Rainwater tanks should be designed to protect the water from contamination by leaves, dust, insects, vermin, and other industrial or agricultural pollutants. Tanks should be sited away from trees, with good fitting lids and kept in good condition. Incoming water should be filtered or screened, or allowed to settle to take out foreign matter. Water, which is relatively clean on entry to the tank, will usually improve in quality if allowed to sit for some time inside the tank. Bacteria entering the tank will die off rapidly if the water is relatively clean. Algae will grow inside a tank if sufficient sunlight is available for photosynthesis. Keeping a tank dark and sited in a shady spot will prevent algae growth and also keep the water cool. As mentioned above, first flush devices help to prevent the dirty ‘first flush’ water from entering the storage tank. The area surrounding a RWH should be kept in good sanitary condition, fenced off to prevent animals fouling the area or children playing around the tank. Any pools of water gathering around the tank should be drained and filled (PRACTICAL ACTION 2008).
Secondly, there is a need to prevent insect vectors from breeding inside the tank. In areas where malaria is present, providing water tanks without any care for preventing insect breeding can cause more problems than it solves. All tanks should be sealed to prevent insects from entering. Mosquito proof screens should be fitted to all openings (PRACTICAL ACTION 2008).
Working PrincipleRainwater collected on the rooftop is transported with gutters to a storage reservoir. There is a wide variety of systems available for RWH systems as well as for treating water before, during and after storage, which helps to prevent water from contamination.
Capacity/AdequacyThe supply is limited by the amount of rainfall and the size of the catchment area and storage reservoir (HATUM & WORM 2006). Storage reservoirs can vary in size from a cubic metre up to hundreds of cubic metres for large projects, but typically up to a maximum of 20 or 30 cubic metres for a domestic system (PRACTICAL ACTION 2008).
PerformanceRainwater is generally better quality than other available or traditional water sources (groundwater may be unusable due to fluoride, salinity or arsenic; HATUM & WORM 2006).
Costs100 to 1000 USD depending on material, storage size and technology.
Self-help CompatibilityDepending on the scale, construction of RWH systems can be very simple and local people can easily be trained to build these themselves. This reduces costs and encourages more participation, ownership and sustainability at community level (HATUM & WORM 2006).
O&MProper operation and regular maintenance is a very important factor that is often neglected. Regular inspection, cleaning, and occasional repairs are essential for the success of a system (HATUM & WORM 2006).
ReliabilityIf well constructed and maintained drinking water in good quality is available.
Main strengthIt provides water, which otherwise would have been lost, at the point of consumption (HATUM & WORM 2006).
Main weaknessLimited supply: The supply is limited by the amount of rainfall and the size of the catchment area and storage reservoir (HATUM & WORM 2006).

Applicability

RTRWH in urban areas can be implemented everywhere from a single household to community level (SHRESTHA 2010): the technology is flexible and adaptable to a very wide variety of conditions. It is used in the richest and the poorest societies, as well as in the wettest and the driest regions on our planet. Collected rainwater can supplement other water sources when they become scarce or are of low quality like brackish groundwater or polluted surface water in the rainy season. It also provides a good alternative and replacement in times of drought or when the water table drops and wells go dry. (HATUM & WORM 2006).

Advantages

  • Local people can easily be trained to build RWH systems themselves. This reduces costs and encourages more participation, ownership and sustainability at community level (HATUM & WORM 2006)
  • Rainwater is better than other available or traditional sources (groundwater may be unusable due to fluoride, salinity or arsenic) (HATUM & WORM 2006)
  • Costs for buying water and time to extract from the city water supply can be saved (SHRESTHA 2010)
  • It provides water at the point of consumption (HATUM & WORM 2006)
  • Not affected by local geology or topography (HATUM & WORM 2006)
  • Almost all roofing material is acceptable for collecting water for household purposes (HATUM & WORM 2006)
  • Rooftop RWH reduces the amount of rainwater going into sewers, drains and may reduce flooding and clogging of water channels and uptakes (WATERAID 2008)

Disadvantages

  • Limited by the amount of rainfall and the size of the catchment area and storage reservoir (HATUM & WORM 2006)
  • Supply is sensitive to droughts: Occurrence of long dry spells and droughts can cause water supply problems (HATUM & WORM 2006)
  • The cost of rainwater catchment systems is almost fully incurred during initial construction (HATUM & WORM 2006)
  • Proper operation and regular maintenance is a very important factor that is often neglected (HATUM & WORM 2006)
  • Rainwater quality may be affected by air pollution, animal or bird droppings, insects, dirt and organic matter (HATUM & WORM 2006)

References

CPREEC (Editor) (n.y.): Rooftop Rainwater Harvesting System. Tamil Nadu: C.P.R. Environmental Education Centre (CPREEC). URL [Accessed: 11.03.2011].
CSE (Editor) (n.y.): Filters developed by WISY. New Delhi: Centre for Science and Environment (CSE). URL [Accessed: 05.01.2011].
HATUM, T.; WORM, J. (2006): Rainwater Harvesting for Domestic USE. Wageningen: Agrosima and CTA. URL [Accessed: 11.03.2011].
PRACTICAL ACTION (Editor) (2008): Rainwater Harvesting. Bourton on Dunsmore: Practical Action, Schumacher Centre for Technology & Development. URL [Accessed: 11.03.2011].
KSCST (Editor) (n.y.): Rainwater Harvesting Filter – “PopUp Filter” – Karnataka. Bangalore: Karnataka State Council for Science and Technology (KSCST). URL [Accessed: 05.01.2011].
RAINWATERCLUB (Editor) (n.y.): Rainwater Harvesting: Rain barrel. Bangalore: RAINWATERCLUB. URL [Accessed: 11.03.2011].
SHRESTHA, R.R. (2010): Eco Home for Sustainable Water Management- A Case Study in Kathmandu. Kathmandu: United Nation Development Program (UNDP). URL [Accessed: 05.01.2011].
THOMAS, T.H.; MARTINSON, D.B. (2007): Roofwater Harvesting: A Handbook for Practitioners. Delft: IRC International Water and Sanitation Centre. URL [Accessed: 11.03.2011].
VISHWANATH, S. (n.y.): Rainwater Harvesting in Urban Areas. Bangalore: RAINWATERCLUB. URL [Accessed: 11.03.2011].
WAN (Editor) (2008): Nepal’s Experiences in Community-Based Water Resource Management. (= Fieldwork paper). Water Aid Nepal (WAN) and End Water Poverty. URL [Accessed: 30.03.2010].
 Thanks
 http://www.sswm.info/category/implementation-tools/water-sources/hardware/precipitation-harvesting/rainwater-harvesting-u

Friday, August 11, 2017

This Device Turns Salt Water Into Drinking Water Using Sunlight




The Eliodomestico is basically a personal desalination still, which operates similar to an “upside down coffee percolator.” The device is an open-source design, noted for its remarkable simplicity to build and use, as specifically intended by Diamanti when creating the solar still.
The device consists of two ceramic pieces that sit on top of one another. Within the top piece is a black container into which the salt water is deposited.
The sun heats the container of water, turning the water into steam. The pressure then builds until the steam is forced into a tube and is deposited into a container, where the water then cools, condenses and collects in the basin.
The Eliodomestico is designed to be carried upon the head when traveling, as is common place in developing countries where water is not a centralized commodity. People often are forced to walk great distances to collect this vital resource.

A revolutionary ceramic solar-powered still has the ability to combat one of the greatest threats to human life in the developing world, water insecurity. The solar still turns salt water into fresh water and can be built for under $50 U.S. dollars.
Water insecurity is one of the biggest issues facing the developing world today, but innovative designer Gabriele Diamanti has created a simple, yet effective, solution.


Method 2

A federally funded research effort to revolutionize water treatment has yielded an off-grid technology that uses energy from sunlight alone to turn salt water into fresh drinking water. The desalination system, which uses a combination of membrane distillation technology and light-harvesting nanophotonics, is the first major innovation from the Center for Nanotechnology Enabled Water Treatment (NEWT), a multi-institutional engineering research center based at Rice University.
NEWT's "nanophotonics-enabled solar membrane distillation" technology, or NESMD, combines tried-and-true water treatment methods with cutting-edge nanotechnology that converts sunlight to heat. The technology is described online this week in the Proceedings of the National Academy of Sciences.
More than 18,000 desalination plants operate in 150 countries, but NEWT's desalination technology is unlike any other used today.
"Direct solar desalination could be a game changer for some of the estimated 1 billion people who lack access to clean drinking water," said Rice scientist and water treatment expert Qilin Li, a corresponding author on the study. "This off-grid technology is capable of providing sufficient clean water for family use in a compact footprint, and it can be scaled up to provide water for larger communities."
The oldest method for making freshwater from salt water is distillation. Salt water is boiled, and the steam is captured and run through a condensing coil. Distillation has been used for centuries, but it requires complex infrastructure and is energy inefficient due to the amount of heat required to boil water and produce steam. More than half the cost of operating a water distillation plant is for energy.
An emerging technology for desalination is membrane distillation, where hot salt water is flowed across one side of a porous membrane and cold freshwater is flowed across the other. Water vapor is naturally drawn through the membrane from the hot to the cold side, and because the seawater need not be boiled, the energy requirements are less than they would be for traditional distillation. However, the energy costs are still significant because heat is continuously lost from the hot side of the membrane to the cold.
"Unlike traditional membrane distillation, NESMD benefits from increasing efficiency with scale," said Rice's Naomi Halas, a corresponding author on the paper and the leader of NEWT's nanophotonics research efforts. "It requires minimal pumping energy for optimal distillate conversion, and there are a number of ways we can further optimize the technology to make it more productive and efficient."
NEWT's new technology builds upon research in Halas' lab to create engineered nanoparticles that harvest as much as 80 percent of sunlight to generate steam. By adding low-cost, commercially available nanoparticles to a porous membrane, NEWT has essentially turned the membrane itself into a one-sided heating element that alone heats the water to drive membrane distillation.
"The integration of photothermal heating capabilities within a water purification membrane for direct, solar-driven desalination opens new opportunities in water purification," said Yale University 's Menachem "Meny" Elimelech, a co-author of the new study and NEWT's lead researcher for membrane processes.
In the PNAS study, researchers offered proof-of-concept results based on tests with an NESMD chamber about the size of three postage stamps and just a few millimeters thick. The distillation membrane in the chamber contained a specially designed top layer of carbon black nanoparticles infused into a porous polymer. The light-capturing nanoparticles heated the entire surface of the membrane when exposed to sunlight. A thin half-millimeter-thick layer of salt water flowed atop the carbon-black layer, and a cool freshwater stream flowed below.
Li, the leader of NEWT's advanced treatment test beds at Rice, said the water production rate increased greatly by concentrating the sunlight. "The intensity got up 17.5 kilowatts per meter squared when a lens was used to concentrate sunlight by 25 times, and the water production increased to about 6 liters per meter squared per hour."
Li said NEWT's research team has already made a much larger system that contains a panel that is about 70 centimeters by 25 centimeters. Ultimately, she said, NEWT hopes to produce a modular system where users could order as many panels as they needed based on their daily water demands.
"You could assemble these together, just as you would the panels in a solar farm," she said. "Depending on the water production rate you need, you could calculate how much membrane area you would need. For example, if you need 20 liters per hour, and the panels produce 6 liters per hour per square meter, you would order a little over 3 square meters of panels."
Established by the National Science Foundation in 2015, NEWT aims to develop compact, mobile, off-grid water-treatment systems that can provide clean water to millions of people who lack it and make U.S. energy production more sustainable and cost-effective. NEWT, which is expected to leverage more than $40 million in federal and industrial support over the next decade, is the first NSF Engineering Research Center (ERC) in Houston and only the third in Texas since NSF began the ERC program in 1985. NEWT focuses on applications for humanitarian emergency response, rural water systems and wastewater treatment and reuse at remote sites, including both onshore and offshore drilling platforms for oil and gas exploration.

Story Source:
Materials provided by Rice University.

Thanks  https://www.sciencedaily.com,http://thefreethoughtproject.com/

Sunday, August 6, 2017

How immersive technologies will reshape networks

Immersive technologies such as virtual reality (VR) and augmented reality (AR) traffic streams will be the next wave of disruption for networks.
Massive growth in video traffic not only increases demand for bandwidth, but also requires lower latency. Video content providers, just as SaaS providers before them, are also being forced to peer at larger numbers of loc...ations to reduce transit latency.
However, the peering model at colocations might not be able to satisfy the latency and compute requirements that will be generated by IoT applications and immersive new services like virtual reality (VR) and augmented reality (AR).
VR and AR use 360-degree video to allow users to see and experience an environment from all angles in order to create the sensation that they are in the digital content they are watching. This immersive experience has tremendous potential in both corporate and consumer applications like tourism, entertainment, corporate meetings, education and health care.
In short, there is a very high probability that VR and AR will produce unprecedented levels of data that will need to be transported across the network.
As a result, last-mile networks will need much higher traffic management capabilities to meet the very low-latency, high-throughput demands of immersive content.
Cecile G. Tamura

Sunday, July 23, 2017

The world's largest floating solar farm

The world’s largest solar farm, located in China, has been connected to the grid and is now producing renewable energy.

Monday, July 17, 2017

“Non-invasive self diagnosis of silent heart attack”.மெளனமாக ஏற்படும் மாரடைப்பை கண்டுபிடிக்கக்கூடிய ஒரு கருவியை


A teenager has developed a technique to detect so-called "silent" heart attacks. 
Akash Manoj, who is thought to be 15 or 16 years old, is a student in Tamil Nadu and discovered a method of analysing a specific protein in the blood that can determine if a patient is at risk.
The schoolboy said he was inspired after his grandfather suffered a heart attack and it is thought the advance could save many lives."Silent heart attacks are extremely deadly and alarmingly common these days. In these cases, almost no symptoms are evident and thus people look so healthy to us," Akash told the India Times. "My grandfather also looked healthy but one day he collapsed following a sudden heart attack."
The technique involves analysing the presence of a protein, FABP3, in the blood, without puncturing the skin.As FAB3 has a negative charge it attracts to positive charges, a property Akash utilised in the detection process. 
UV light is passed through the skin and a sensor detects the amount of protein present.
Akash has been honoured for his discovery and has been invited to partake in the "Innovation Scholars In-Residence Programme".
தமிழகத்தைச் சேர்ந்த 15 வயது ஆகாஷ் மனோஜ், மெளனமாக ஏற்படும் மாரடைப்பை கண்டுபிடிக்கக்கூடிய ஒரு கருவியை உருவாக்கியுள்ளார். சைலண்ட் ஹார்ட் அட்டாக் பலருக்கு ஏற்படுவதா...
ல் அதைப் பற்றி தெரியாமலே வாழ்ந்து கொண்டிருக்கின்றனர். ஆனால் அது கண்டுபிடிக்கப்பட்டால் பலரது உயிர் காக்கப்படும், அதன் முதல் அடியே ஆகாஷ் கண்டுபிடித்துள்ள கருவி.பொதுவாக மாரடைப்பு ஏற்படுவதற்கு முன்பு மார் வலி, மூச்சுத்திணறல் போன்ற சில அறிகுறிகள் ஏற்படும். ஆனால் சைலண்ட் ஹார்ட் அடாக் ஏற்படுவோருக்கு இதுபோன்று எதுவும் வருவதில்லை. அதுபோன்ற சமயத்தில் பலரும் அதை சாதரண ஜுரம், உடல்வலி என்று தவறாக நினைத்துக் கொள்கின்றனர். வரவிருக்கும் ஆபத்தை உணராமல் தாங்கள் ஆரோக்கியமாக இருப்பதாக பலரும் ஏமாந்து போகின்றனர்.
ஆகாஷின் தாத்தாவிற்கு இதுபோன்று ஒருமுறை சைலண்ட் மாரடைப்பு ஏற்பட்டது பின்னாளில் கண்டுபிடிக்கப்பட்டது. அதை தொடர்ந்து இதை கண்டுபிடிக்க ஒரு கருவி தேவை என யோசித்த ஆகாஷ் ஆய்வில் இறங்கினார்.


“என் தாத்தா ஒரு சர்க்கரை நோயாளி, அதிக ரத்த அழுத்தமும் உடையவர். ஆனால் ஆரோக்கியமாக இருந்தார். ஒருமுறை உள்ளுக்குள்ளே ஏற்பட்ட மாரடைப்பில் நிலைகுலைந்து இறந்து போனார்,”
என்று ஹிந்துஸ்தான் டைம்ஸ் பேட்டியில் கூறினார் ஆகாஷ். ஆகாஷுக்கு மருத்துவ ஆய்வுகள் என்றால் அதீத ஆர்வம். எட்டாம் வகுப்பு படிக்கும்போதில் இருந்தே மருத்துவம் சம்மந்தமான ஆராய்ச்சிகளை படிப்பார். பெங்களுருவில் உள்ள இந்தியன் இன்ஸ்டிடூட் ஆப் சயின்ஸ் மையத்தின் நூலகத்துக்கு சென்று அவ்வப்போது படித்து தன் அறிவை பெருக்கிக் கொள்வார் ஆகாஷ். ஹோசூரில் வாழும் ஆகாஷுக்கு அந்த மையம் ஒரு மணி நேர தூரத்தில் இருப்பதால் அந்த நூலகம் செல்வதை வழக்கமாக கொண்டிருந்தார்.
ஆய்வுக் கட்டுரைகள் எடுத்து படிக்க அதிக விலை கொடுக்கவேண்டி இருந்தது. அதனால் நூலகங்கள் சென்று படிக்கத்தொடங்கினார் ஆகாஷ்.
நான் படித்துள்ள ஆய்வுகளுக்கு கட்டணம் செலுத்தவேண்டி இருந்தால் அது கோடிகளை தாண்டி இருக்கும் என்கிறார். மருத்துவ அறிவியலில் ஆர்வம் மிகுதியால் அது சம்மந்த ஜர்னல்களை எடுத்து படிப்பது எனக்கு பிடிக்கும் என்கிறார்.
துளையில்லா தொழில்நுட்ப முறையைக் கொண்டு ஆகாஷ் இந்த கருவியை உருவாக்கினார். இது ரத்தத்தில் ப்ரோடீன், FABP3 இருப்பதை கண்டுபிடிக்கும். ஒருவரின் மணிக்கட்டு அல்லது காதுப் பகுதியில் பின்னால் பொருத்திடவேண்டும். ஹஃப்பிங்க்டன் போஸ்ட் பேட்டியில் கூறிய ஆகாஷ்,
“ப்ரோடீன் வகைகளில் மிகச்சிறிய வகை FABP3 ஆகும். ரத்தத்தில் இருக்கும் இது பொதுவாக நெகட்டிவாக சார்ஜ் ஆகியிருக்கும். அதனால் பாசிட்டிவ் சார்ஜ் நோக்கி இது ஈர்க்கப்படும். இந்த தன்மையை நான் என் தொழில்நுட்பத்தில் பயன்படுத்தினேன்,” என்றார்.
அண்மையில் ராஷ்ட்ரபதி பவனில் குடியரசு தலைவர் ப்ரனாப் முகர்ஜி, ஆகாஷை தனது விருந்தினராக அழைத்து பாராட்டினார். Innovation Scholars In-Residence திட்டத்தின் கீழ் அவர் அழைக்கப்பட்டார். தனது கருவி பல உயிர்களை காக்க உதவும் குறிப்பாக ஊரக பகுதிகளில் வாழும் மக்களுக்கு உதவிகரமாக இருக்கும் என்று நம்பிக்கையாக உள்ளார் ஆகாஷ். இக்கருவிக்கான காப்புரிமை பெற விண்ணப்பித்துள்ளார். பொது மக்களின் நலனுக்காக இந்த கருவியை இந்திய அரசாங்கம் பயன்படுத்தவேண்டும் என்று தனது ஆசையை தெரிவித்துள்ளார்.
ஆகாஷ் கார்டியாலஜி துறையில் படிக்க விழைகிறார். டெல்லி ஏய்ம்ஸ் கல்லூரியில் படிக்கவேண்டும் என்று விருப்பப்படுகிறார் இவர். இந்த இளம் வயதில் தனது ஆர்வத்தை ஒரு பயனுக்காக பயன்படுத்தி எல்லாருடைய வாழ்விலும் மாற்றத்தை ஏற்படுத்த முனையும் இச்சிறுவன் நன் நாட்டிற்கு கிடைத்துள்ள பொக்கிஷம். இவருக்கு நமது வாழ்த்துக்கள்.

Friday, June 16, 2017

Computer Recycling

Computers are an integral part of daily life, but as they and other electronic devices become obsolete more and more quickly, we're faced with the growing problem of disposing of all our e-waste properly. A UN initiative called StEP (Solving the E-waste Problem) estimates that by 2017 there will be 65.4 million tonnes of e-waste generated globally every year. And Australians contribute more than their fair share of that, with each of us generating 25 kilos a year.
e-waste, discarded computer equipment comprises monitors, printers, hard drives and circuit boards. Such items should on no account be thrown out with your household rubbish because they contain toxic substances, and are effectively hazardous waste. E-waste often ends up in the developing world, and the UN’s Environment Programme is alarmed by the amount of electronic goods which is improperly disposed of overseas. There is increasing concern about the pollution caused by hazardous chemicals and heavy metals in Africa, Asia and South America.
What’s in my PC?
MaterialProportion
Plastic
Ferrous metals
Non-ferrous metals
Electronic boards
Glass
23%
32%
18%
12%
15%
A single computer can contain up to 2kg of lead, and the complex mixture of materials make PCs very difficult to recycle.
Electronic products thrown into landfill leak toxic materials into soil and water, resulting in contamination of the food chain. Additionally, rare and non-renewable materials are wasted instead of being re-used. New government-backed recycling efforts have been put in place across most of Australia to meet the national e-recycling target of 80 per cent by the end of 2021.

Where to donate your computer to be refurbished in Australia

If your computer's not too old and still in good nick, there are some community recycling initiatives that refurbish computers and offer them to nonprofit groups.
Some Technical Aid to the Disabled organisations are registered refurbishers, while others may accept donations on a case-by-case basis. Contact your state or territory's branch and ask if they accept computer donations.

Other computer refurbishers include:

  • Business to Community Recyclers (Vic) 
  • Computerbank (Vic)
  • Computerbank (Qld)
  • Computerbank (Newcastle)
Planet Ark's Recycling Near You website lets you search by area or product to find a local recycling centre.
Give Now has a list of places that can refurbish computers nationally.

Why is e-waste so bad?

Toxic materials and hazardous chemicals are often used in the manufacture of computer and electronic equipment, and when parts are disposed of improperly these chemicals can leach into soil and water and lead to environmental contamination.
To prevent hazardous chemicals from leaking into soil and storm water drains, computer and electronic equipment must not be thrown out with your rubbish. Also avoid leaving computer waste standing outside for long periods, particularly during wet weather.
While manufacturing methods are said to have improved, many companies continue to use toxic chemicals and primary materials over recycled parts.

What chemicals are in my e-waste?

The roll call of toxic materials is long and includes:
  • Mercury (used in LCD screens)
  • Lead 
  • Cadmium (used in batteries) - known to cause cancer in humans
  • Beryllium (found in motherboards) - a known carcinogen and can cause lung disorders if inhaled
  • Chromium (used to prevent corrosion) - can cause liver and kidney damage as well as skin reactions
  • Antimony - can cause gastrointestinal disorders
  • Arsenic - a known carcinogen
  • Brominated flame retardants (used in circuit boards, cables and plastic casing) and polyvinyl chloride (PVC) (used in casing and connectors) - toxic when burned and can collect in the environment.