Introduction
Manual drafting is the practice of creating drawings by hand. Manual drafting techniques have traditionally enabled the planning and communication of design ideas and construction information. As there is a very diverse range of information that may need to be communicated, there are a similarly wide range of drawing types. See Types of drawing for more information.
The evolution of manual drafting techniques has created a discipline around which other forms of drafting, such as computer-aided design (CAD) have subsequently developed.
The advantages of manual drafting include; the low cost of equipment compared to CAD hardware and software, the clarity that can be achieved by being able to see all shapes, sizes and angles on one sheet, the ability to bring creative style and expression to drawings, and a degree of depth and weight that can be easier to convey with 'analogue' rather than 'digital' drawing techniques. Those with experience of manual drafting would agree it gives a much deeper sense of knowledge and understanding of the drawing and then the finished building compared with CAD. Indeed some find it easier to sketch, in pencil, their drawing on paper then produce it on CAD.
However, manual drafting is now becoming something of a lost art, as; it requires a large amount of space, both for the drawing process, storage and viewing; drawings cannot be linked to digital information, they can take much more time to prepare in comparison with CAD drawings, they are more difficult to correct, text and colour can be more difficult to apply, it is more complicated to create three-dimensional representations, with isometric being the most common and a lot of experience is needed to complete a drawing efficiently without wasting too much time.
Those with experience can churn out a drawing just as quickly as a CAD drawing but the effort getting to that level is much higher compared to using CAD. Their is a lot more cost with manual drawings as draughts people would need to be employed.
Equipment
Manual drafting requires a flat drafting table, drafting or drawing board, typically with a parallel motion, that allows consistent drawing of parallel lines. Drawing boards can often be adjusted in height and angle to suit the user. Typically with light from the north falling on the paper, from top or behind, the board is angled for drawing and flat for tracing. The angle aids in keeping your set square against the sliding ruler (if you needed to draw 90° lines) and helping with good posture.
Vellum paper was used traditionally for drafting and came supplied in rolls. More recently, drafting paper, standard paper sheets, or tracing paper have become more common as they are less expensive.
A range of paper sizes are available suitable for different purposes. See Paper sizes for more information.
Manual drafting tools include:
Specialised pencils with varying lead hardness.
Technical drawing pens of varying sizes (see technical drawing pen sizes for more information).
Colour application pens.
Scale rules.
Set squares.
T squares.
Steel rules that are not damaged by being used repeatedly to draw lines.
Compasses.
Protractors.
Dividers.
Drafting tape, masking tape (3M Magic removable tape and glue dots work well too) or stainless steel clips to secure the corners of the sheet to the board.
Pencil sharpeners.
Of a kind to give sharp angles to the pencil, showing about 5-6 mm of pencil lead
Many used craft knifes or scalpels to sharpen.
Erasers.
Pen cleaners.
Scalpel blades for:
Clear tape for repairing drawings (this does not show on reproductions)
Mechanical lead holders for using various size leads for different parts of the draft.
Templates or stencils allowing easy drawing of certain objects, symbols, common shapes, text, and so on.
Text writing machines.
Letraset lettering sheets that can be applied to drawings as a form of transfer. Other sheets include people, trees and other common objects and symbols.
Pantone colour and greyscale sheets than can be cut and applied to drawings to bock colour or shade areas.
Correction fluid - Tipex (which does not show on reproductions).
Drawing board attachments that can be fixed to the parallel motion ruler to create specific angles, reproduce lines or change scales.
Lines
Lines in manual drafts should be clean and sharp. A straight edge should always be used when manually drafting. A parallel motion, or T-square can be used to draw horizontal lines, and a T-square or set square to draw vertical lines or other common angles.
Typically, the bottom of the set square is placed on the top of the parallel motion, and the vertical portion used to draw straight lines. To draw a vertical line using a T-square, the T portion should be placed flat against the top of the drawing board.
Equal pressure should be applied on the pen or pencil when drawing lines, slightly rotating the point, and not removing it from the paper until the line is completed.
Sprinkling setting powder, or using fixing sprays over pencil lines can help maintain the integrity of the lines when the sheets are folded or rolled, or otherwise brushed against.
Line weights
Manual drafting techniques typically involve drawing different line weights to represent different items. Different line weights can be created by using a different size mechanical pencil lead, or a different size of technical drawing pen.
Exterior walls are typically drawn on floor plans and sections with heavy, solid lines. Windows may be drawn lighter, or with the same heaviness but in a dash-dot-dash format. Interior walls have slightly lighter line weights. Elements such as fittings should be drawn with the lightest line weight, and sometimes dashed lines.
Lettering
It is important to maintain correct lettering sizes in manual draft, for example:
Notes: 3/32 inch letters.
Special notes: 1/8 inch letters.
Titles: 1/4 inch letters.
F pencils or technical drawing pens are typically used for lettering, with a small right triangle to draw straight portions of the letter. Curved portions may be drawn freehand. Thicker strokes are used for horizontal lines, thinner strokes for vertical lines. It can be useful to draw light guidelines first to ensure the correct and uniform text height.
This is a carefully practiced skill and Frank Chings book "Architectural graphics" shows practice papers of the kind primary school children use to get the lettering right. Alternatively just writing 4 mm x 4 mm capital letters looks right for most manual drawings.
Alternatively, stencils, transfers or writing machines may be used.
Scale
Scale, or depicting objects and spaces at a specific ratio to their actual size, is a critical to precise manual drafting techniques. Mechanical draft creators use different scales, or the amount that objects being drawn are reduced or enlarged. Floor plans generally are drawn with 1/4 inch equaling one inch, kitchens and bathrooms are drawn with a 1/2 inch scale and wall sections are drawn with a 3/4 inch scale.
Projections
There are a number of techniques of projection that can be used to represent three-dimensional objects in two-dimensions by 'projecting' their image onto a planar surface.
See Drawing projections for more information.
Notation and units
Standard notation conventions should be followed so that there is clear communication between different people and mistakes are avoided.
See Notation and units for more information.
Symbols
A range of standard symbols and hatching techniques can be used to convey recognised meaning without the need for explanation.
See Symbols on architectural drawings for more information.
Thanks;https://www.designingbuildings.co.uk
